Adjustable anchor systems

Words: Mike Ripley/Public/News/20111010101000-1.jpg" width="600" height="338" border="0" alt="Adjustable anchor systems available through Wire-Bond" />
Adjustable anchor systems available through Wire-Bond
Our two most popular adjustable anchor systems have steel back plates, available in 14 and 12 gauge, with eyes or slots that accommodate the adjustable 3/16-diameter ties (see Image A). Both anchor plates can be modified for different thicknesses of insulation. Either the legs are lengthened for the plate with eyes or the usage of prongs with the slotted plate (see Image B). When insulation is scored 16 inches high X 8-feet-long sections, the plate with legs is an excellent choice as the legs act as a platform for the insulation to rest.

When the adjustable hook is inserted in the eye, it will fit tightly against the insulation and help to hold it in place. Another benefit of using this anchor is the ease of fastening to the steel stud. The installer can visually find the stud, since the insulation is on the outside of the anchor and uses a standard #10 X 1 1/2-inch hex head screw with washer to fasten plate to stud or board. If the 4- X 8-feet sheets of insulation are used, the plates with prongs are a better choice as they will pierce the insulation, pinning it against the wallboard or stud, and provide positive connection to the steel stud. This product requires an experienced installer as the margin of error is small, since the prongs are about 1 inch wide being applied to a 1 1/2-inch-wide stud through various thicknesses of rigid insulation.

Another adjustable anchor system that is gaining attention is a barrel-shaped anchor with threads at one end and a single loop at the opposite end that accepts an adjustable 3/16-inch wire tie (see Image C). The barrel or post anchor, like the plate anchors, can vary in size for different widths of insulation and easily be modified for seismic applications. The threads are either carbon steel for penetrating steel studs with a polymer coating, or Tapcon parts 1/4-inch in diameter with a blue polymer coating for concrete or CMU applications. This anchor system is a good alternative to the prong-type anchors, especially for wider sizes of insulation, because it gives the installer a wider margin of error since it’s smaller. Being a single barrel makes it more “green,” as it only punctures one hole in the insulation versus four with the prong products (two prongs and two screws). It can be installed rapidly by using a chuck adapter that fits over the loop part.

All three products meet ACI 530 Code Seismic Design Requirements for Categories E and F by adding either a welded or plastic clip to the adjustable tie embedded in the mortar joint of the veneer. The clips provide a channel for a continuous, single-strand, 9-gauge wire to run horizontally along the veneer.
About: Featured
 0
Masonry Mortar: The Right Type for the Job
May 2025

When it comes to masonry construction, mortar is much more than “glue” that holds everything together — it’s a critical component of wall performance, longevity, and aesthetics. It can “make it or break it”. Whether you’re laying a foundation CMU wall or

Garen Graves
Featured MAP Partner
Mortar
Read More
MASONRY STRONG Podcast, Episode 20 Recap: Mark Kemp, Superior Masonry
May 2025

Justin Stengel
Read More
How It’s Made: Clay Thin Brick
May 2025

Clay thin brick is a versatile alternative to traditional full brick. It comes in numerous colors and styles and offers something for every design preference. Thanks to the lighter weight, it is designed to reach spaces full brick cannot. From floors to c

Allison Goley
Featured MAP Partner
Read More
Bonding with Masonry 2025: Q1
May 2025

This issue’s questions come from an Architect and a Mason Contractor. What questions do you have? Send them to info@masonrymagazine.com, attention Technical Talk. Q. An Architect asks how to create a narrow masonry pier between openings. Is there a min

David Biggs
Featured
Read More